This British Standard is the official English language version of. EN Together wi th BS EN i t supersedes. BS EN l which. BS EN BRITISH STANDARDOffshore containers and associated lifting sets — Part 1: Offshore containers — Design, manufacture. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European.

Author: Mazushakar Samuzahn
Country: Senegal
Language: English (Spanish)
Genre: Business
Published (Last): 19 December 2018
Pages: 438
PDF File Size: 14.95 Mb
ePub File Size: 16.97 Mb
ISBN: 307-9-70067-964-6
Downloads: 31053
Price: Free* [*Free Regsitration Required]
Uploader: Zololmaran

In order to avoid initiation of brittle fracture, the steels shall possess adequate fracture energy.

Full text of “Safety British Standards”

Requirements for the lifting set and for non-transport related requirements, relating to offshore service containers, e. NOTE 3 For containers with special features, additional design requirements may apply. When simplified calculations are used, and each beam is considered separately, any assumptions concerning support conditions shall be stated.

Where containers are designed for stacking, and the lifting set hangs over the side of the top frame they shall be fitted with a method of protection for those exposed parts, e. Table 1 — Charpy impact test temperature: Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover.

Technical delivery requirements ENCold formed welded structural hollow sections of non-alloy and fine grain steels – Part 1: NOTE 2 Care should be taken in the storage of calibrated concrete blocks so as prevent the absorption of water having an influence on the actual block mass. General principles ENNon-destructive examination of fusion welds — Visual examination ENNon-destructive examination of welds – Penetrant testing of welds – Acceptance levels ENNon-destructive examination of welds – Magnetic particle examination of welds ENNon-destructive examination of welds – Magnetic particle testing of welds – Acceptance levels ENNon-destructive examination of welds – Radiographic examination of welded joints ENNon-destructive examination of welds – Ultrasonic examination of welded joints – Acceptance levels ENNon-destructive examination of welds – Ultrasonic examination of welded joints ENMetallic materials — Tensile testing — Part 1: NOTE 4 Cracks in welds and minor deformations may be repaired.

  D44H11 DATASHEET PDF

Other parts of the standard are: Hinges shall be protected against damage from impact loads.

A version in any other ns made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions. NOTE 2 The data plate may be combined with the inspection plate by including the additional information specified in Clause 5 of Gs The chemical composition shall be in accordance with that set out in Table 2 and mechanical properties shall be in accordance with Table 3. When materials of different galvanic potential are joined together, the design shall be such that galvanic corrosion is avoided.

June Replaced By: It recommends that new offshore containers be approved, prototype tested and certified by duly authorized bodies. To determine the resulting sling force on the pad eyes, the sling angle shall be taken into account, so that the resulting sling force on each pad eye is calculated as follows: No significant permanent damage shall occur. Aluminium rivets have been found to be unsuitable as a fixing method in the offshore environment and shall not be used.

To avoid confusion, the plate shall not carry the date of the next inspection. These shall be agreed in advance with the certifying body. Ideally, dynamic calculations or tests should be carried out to verify the ability of a container to withstand such loads.

BS EN 12079-1:2006

Information regarding online access to British Standards via British Standards Online can be found at http: The inspection methods and the quality of the welds shall be described by the NDE operator and included in the inspection report. Pad eyes shall be designed for a total vertical force of 3 R g.

Locking arrangements shall be protected to prevent dislodgement by impact. Any external connections, e.

  KINGDOM OF NITHIA PDF

As dynamic calculations would be very complex, it is usually sufficient to verify the strength by a vertical impact test as described in 7. This force may act in any horizontal direction on the comer post. The impact test temperature shall be equal to the design air temperature, T n see 4 and 5. The repairer shall ensure the quality of these procedures and facilities by a certified quality assurance system at least in accordance with EN ISO NOTE Equipment permanently installed on a container is considered to be part of the container for een purposes.

BS EN 海岸集装箱及其相关提升设备 第1部分:海岸集装箱 设计丶制造和标记 – MBA智库文档

Where design requirements are based on the gravitational forces derived from these values, those forces are indicated thus: For specimens with their axis transverse to the final rolling direction the valve shall be two thirds of that for longitudinally orientated specimens.

Non- destructive examination NDE hs be required after testing. The welding of the secondary structure shall be according to EN Aluminium rivets have been found to be unsuitable as a fixing method in the offshore environment and shall not be used. C Inspection certificate 3. It shall be built in conformity with plans and data and using tooling comparable to those planned for subsequent production. It is ne constant aim of BSI to improve the quality of our products and services.

Lifting sets – Design, manufacture and marking [8] ENOffshore containers and associated lifting sets – Part 3: It shall be held 120791- 5 minutes before measurements are taken.

Auslegung, Herstellung und Kennzeichnung. CopyrightCopyright subsists in all BSI publications. Drainage facilities, where fitted, shall be examined, e. Rg, Tg and Pg the units of which are in newtons or multiples hs. Such forgings shall be made from fully-killed and fine-grain treated non-ageing steel.