Les routeurs Cisco et IOS. Configuration de la route par défaut. En mode configuration ip route adrIPReseau masque adrIPGateway route statique. Le pare-feu VPN sans fil N Cisco RVW comprend: la prise en charge du routage statique, versions RIP (Routing Information Protocol) 1 et 2 et du routage. CONFIGURATIONS LINUX Vérifiez que ROUTEUR CISCO IOS: a , ROUTEUR QUAGGA A interface.

Author: Shakajind Maujind
Country: Solomon Islands
Language: English (Spanish)
Genre: Art
Published (Last): 15 February 2011
Pages: 271
PDF File Size: 16.86 Mb
ePub File Size: 7.31 Mb
ISBN: 846-7-40495-946-7
Downloads: 58662
Price: Free* [*Free Regsitration Required]
Uploader: Malagrel

The gateway of PC is router2 which connected the Internet, but when PC visit servers in intranet, firstly the request will routafe sent to router2.

The commands to add a static route are as follows: Static routes can also be added by specifying the exit interface rather than the “next hop” IP address of the router. Find out more or Sign In. The simple syntax of static route: Your browser does not support Configurarion. IGRP has an administrative distance of Configure a Static Route. Type the username and password in the login page. Administrative distance is the value from 0 to Network configurations are not restricted to a single static route per destination: TP-Link takes your privacy seriously.

Step 4 Configration Add New…. In most Linux distributions, a static route can be added using the iproute2 command.

Configure a Static Route

Discard —Select to drop packets that are addressed cobfiguration this destination. Perform the following task to configure Static Routes or a default route for a virtual router on the firewall. OSPF has an administrative distance of Click the IP or IPv6 confguration to specify the As the administrator of the network, you are tasked to connect them so that employees in the two LANs can communicate with each other.

  ARDSNET GUIDELINES PDF

Because there is no route to server1 and server2 on route table of router2, thus the request will be thrown away. It means we have to add static route to both R0 and R1 so that R0 and R1 can communicate.

Now try to ping each far end network Note: This page was last edited on 26 Decemberat R1 config ip route Business Wireless Takes your enterprise Wi-Fi to new levels.

R0 show ip route. These parameters are straightforward and easy xtatique understand. In this tutorial we will connect two routers via static route with GNS3.

Configure a Static Route

Switches Boosts your business network with premium performance. Enterprise-level Cisco routers are configurable using the Cisco IOS command line, rather than a web management interface. Network Resources Free Router Simulators. Please refer to following introduction xonfiguration input parameter.

Thank you We appreciate your feedback. And the page of Static Routing would appear on the screen: By using this site, you agree to the Terms of Use and Privacy Policy. Sign Up Follow Us www. Choose this option if you want either unicast or multicast traffic to use the route.

Static route is often used when your network has only a few routers or there is only one route from a source to a destination. Directly connected routes have an administrative distance of 0.

  JIWA HAMBA USMAN AWANG PDF

The route with the lowest administrative distance value is the preferred route that the router selects. Static route tells the device exactly where to send traffic, no matter what. Your feedback helps improve this site.

How to configure Static Routing on wireless routers? | TP-Link

In 2 nd bar, type the IP subnet mask for this destination. Static Route Overview Static Route Overview If you decide that you want specific Layer 3 traffic to take a certain configurafion without participating in IP routing protocols, you None —Select if there is no next hop for the route. Please turn it on for the best experience. Dynamic routes, on the other hand, use a routing protocol to determine the best path and the routes can be changed depending on specific parameters like bandwidth, delay, cost….

How to configure Static Routing on wireless routers?

The administrative distance is a measure of trustworthiness icsco lower numbers are considered to be more trustworthy than higher numbers. User Application Requirement Updated Reverse-Path Forwarding PIM uses reverse-path forwarding RPF to prevent routing loops and to build a shortest-path tree from the receiver back to the multicast source. Static routing can have some potential disadvantages: